Wire Rope

We only offer the highest grade of stainless steel: Type 316L

From $0.35 / ft

Lifeline Threaded Terminal (LLTT)

The work horse of cable railing systems, assumes you can pass through your post with a threaded bolt and get a nut and washer on the back side.

From $3.00 ea

Wrench Flat Threaded Terminal (WFTT)

Same as a Lifeline Threaded Terminal with the addition of a “wrench flat” in between the shaft and the threads.

From $3.00

Extra Long Threaded Terminal (XLTT)

10″ Threaded Terminal with 8″ of thread, designed to be cut to the length required or used full length. If you are passing through a 8 x 8 post or built up/wrapped post it may be preferable to the extra length.

From $5.75

Field Swage Lag Screw (FSLS)

Installs like a screw where passing through the post with a Threaded Terminal isn’t possible or is undesirable.

From $3.00 ea

Lag Screw Turnbuckle (LSTB)

Used when it’s not desirable to pass through the post or attaching directly to the house. Can be used at a angle instead of a Surface Mount Turnbuckle.

From $11.50 ea

Surface Mount Deck Toggle (SMDT)

Used for angles on stairs or changes in pitch where the post is at a angle to cable termination.

From $3.50 ea

Locking Toggle (LKTG)

The Locking Toggle is used on hollow metal posts where it’s not possible or preferable to pass through the post.

From $3.00 ea

Surface Mount Turnbuckle (SMTB)

Used when it’s not desirable to pass through the post and/or on a angle such as on stairs or where the cable is at a angle to the terminal post. Swivel tab will take any angle desired.

From $11.50 ea

Drop Pin Terminal (DRPT)

Used in hollow metal posts where a threaded terminal or pass through terminal won’t work or is undesirable.

From $3.50 ea

Drop Pin Turnbuckle (DRTB)

Used in hollow metal posts where a threaded terminal/ pass through terminal or surface mount won’t work or is undesirable.

From $11.50 ea

Open Jaw Deck Toggle (OJDT)

Installs on a tab or eye bolt, fixed fitting, requires a tensioning fitting on the other end, typically a Open Jaw Turnbuckle.

From $5.00 ea

Open Jaw Turnbuckle (OJTB)

Installs on a tab or eye bolt, 3″ of thread travel.

From $12.00 ea

Inline Turnbuckle (ILTB)

Installs in the middle of a strand between two “fixed” fittings such as Lags Screws or Surface Mount Deck Toggles, commonly on a long strand that would otherwise be difficult to tension.

From $11.50 ea

Invisible Receivers (INVR)

Invisible Receivers use a threaded body and short threaded stud to conceal the threads of stud. The Threaded Body replaces a standard nut with a female receiver body. The heads have a recessed hex key and are tightened using a allen wrench. Each style of Invisible Receiver has a matching fixed fitting with a duplicate head but is a non tensioning fixed end. You can use Invisible Receivers on both ends of a strand or use a fixed head for one end and the Invisible Receiver to do the tensioning at the other end.

Fixed Stemball (STEM)

Used when a flush fit head or a short “disappearing” fitting is desired in either a wood or metal post, there is a different version for each.

From $3.00 ea

Stainless Steel Protector Sleeve (SSPS)

Used on wood posts at double posted corners where the cable is jumping across from one corner post to the other where the cable would otherwise cut into the wood.

$1.00 ea

Stainless Steel Bevel Washer (SSBW)

Used in conjunction with a threaded terminal on stairs where the terminal passes through the post at the angle of the stairs, replaces a flat washer to keep the nut square to the thread.

From $3.00 ea

Dome Cap (RDCP)

Stainless Steel Dome Cap, threads on to a 1/4″ of thread to cover the nut.

From $3.00 ea

Flat Cap (FLCP)

Stainless Steel Flat Cap, threads on to a 1/4″ of thread to cover the nut.

From $3.00 ea

Hex Cap

Inexpensive, simple polypropylene push on hex cap fits the 7/16″ nut on all our  threaded terminals.

$ .25 ea

Acorn Nut (ACRN)

1/4″ x 20 Acorn nut for all our Threaded Terminals

$ .25 ea

Plastic Grommet (PLGR)

Plastic grommets used in metal posts to isolate the stainless steel wire rope from the post hole, especially necessary in aluminum posts where contact between the two dissimilar metals could otherwise set up electrolysis or in a bare steel hole that may otherwise transfer rust residue to the wire.

From $0.10 ea

Rescue Studs

The Rescue Stud is used to salvage a length of cable that for one reason or another needs a new terminal end, either because the strand was cut too short or the current terminal needs to be changed or that terminal has failed…

From  $3.00 ea

Standard Assemblies

Our standard assemblies include a length of 1/8″ cable with a 4 1/4″ threaded terminal machine swaged to one end. The second end is an identical 4 1/4″ threaded terminal that you will hand swage once you have determined your final length.

From  $17.15 ea

Hand Swage Tool for 1/8″ Stud Fittings

Hand swage crimping tool for 1/8″ Stud Fittings, available to buy or borrow on a $90 deposit, keep it or return it for a full refund.

$90.00 ea

Cleaners and Protectants

Even the highest grade of Stainless Steel are subject to oxidation and corrosion or it would be referred to as Stain-proof instead of Stain-less Steel. Two of the best products we have found for rust removal and rust protection were developed by the Boeing Company for the aerospace industry.

$13.00 & $22.00